Silicom’s Quad Port Copper Gigabit Ethernet PCI Express Bypass Server adapter is PCI-Express X4 Copper Gigabit Ethernet network interface card that is based on a single chip, non-Bridged quad port GBE controller. Silicom’s Quad Port Gigabit Ethernet Bypass server adapter supports Normal, Disconnect and Bypass modes.
In Normal mode, the ports are independent interfaces. In Bypass mode, all packets received from one port are transmitted to adjacent port. In Disconnect mode, the adapter simulates switch / rout cable disconnection.
This product is no longer in stock
Availability date:
Silicom’s Quad Port Copper Gigabit Ethernet PCI Express Bypass Server adapter is PCI-Express X4 Copper Gigabit Ethernet network interface card that is based on a single chip, non-Bridged quad port GBE controller. Silicom’s Quad Port Gigabit Ethernet Bypass server adapter supports Normal, Disconnect and Bypass modes.
In Normal mode, the ports are independent interfaces. In Bypass mode, all packets received from one port are transmitted to adjacent port. In Disconnect mode, the adapter simulates switch / rout cable disconnection.
In Bypass mode, the connections of the Ethernet ports are disconnected from the system and switched over to the other port to create a crossed connection loop-back between the Ethernet ports.
Hence, in bypass mode all packets received from one port are transmitted to the adjacent port and vice versa. This feature enables to bypass a failed system and provides maximum up time for the network.
In Disconnect mode, the adapter simulates switch / router cable disconnection. In Disconnect mode, the switch / router does not detect link partner of the adapter.
Silicom’s Quad Port Copper Gigabit Ethernet PCI Express Bypass server adapters include an on board WDT (Watch Dog Timer) controller. The adapter’s software drivers or software application can write commands to the on board WDT controller. The adapter’s software drivers, WDT controller and the Bypass circuitry provide an interface that control and manage the mode of the adapter.
Silicom’s Quad Port Copper Gigabit Ethernet PCI Express Bypass Server adapter is the ideal solution for implementing multiple network segments, mission-critical high-powered networking applications and environments within high performance servers.
Silicom’s Quad Port Copper Gigabit Ethernet Bypass Server adapter is based on Intel i350 Quad port Gigabit Ethernet MAC+PHY of Intel Controller. The Silicom i350 support PCI-SIG Single-Root I/O virtualization and sharing specification (SR-IOV).
Performance:
Bypass:
Copper Gigabit Ethernet 1000Base-T:
Common Key Features:
Bypass Specifications | |
WDT Interval (Software Programmable): | 3,276,800 mSec (3,276.8 Sec): Maximum 100 mSec ( 0.1 Sec) : Minimum WDT Interval = (2^wdt_interval_parameter)*(0.1) sec. wdt_interval_parameter: { Valid Range: 0-15} |
Copper Gigabit Ethernet Technical Specifications - (1000Base-T) Adapters: | |
IEEE Standard / Network topology: | Gigabit Ethernet, 1000Base-T Fast Ethernet, 100Base-TX Ethernet, 10Base-T |
Full duplex / Simplex | Support both Simplex & Full duplex operation in all operating speeds |
Auto negotiation: | Auto-negotiation between Full duplex and simplex operations and between 10Mb/s 100Mb/s speeds and duplex 1000Mb/s. |
Data Transfer Rate: | 1000 Mb/s, 100 Mb/s and 10 Mb/sec in simplex mode per port. 2000Mb/s 200 and 20 Mb/s in full duplex mode per port. |
Cables and Operating distance: | 10Base-T Category 3, 4, or 5 maximum 50m * 100Base-Tx Category 5 maximum 50m * 1000Base-T Category 5E maximum 50m * *Theoretical Distance – Defined as half a distance as stated by the IEEE 802.3 standard |
Operating Systems Support | |
Operating system support: | Linux |
General Technical Specifications | |
Interface Standard: | PCI-Express Base Specification Revision 2.1 ( 5 GTs) |
Board Size: | Low profile short add-in card: 167.64mm X 68.91mm (6.60”X 2.713”) |
PCI Express Card Type: | X4 Lane |
PCI Express Voltage: | +3.3V +-9%, +12V +- 8% |
PCI Connector: | Gold Finger: X4 |
Controller: : | Intel i350AM4 |
I/O: | Quad RJ45 located on edge of the board |
Power Consumption: | Normal mode: 4.68W, 0.39A at 12V: Typical all ports operate at 1000Mb/s. 3.36W, 0.28A at 12V: Typical all ports operate at 100Mb/s. 3.24W, 0.27A at 12V: Typical all ports operate at 10Mb/s. 2.52W, 0.21A at 12V: Typical No link at all ports. Bypass mode: 2.52W, 0.21A at 12V: Typical Bypass Mode Disconnect mode: 2.52W, 0.21A at 12V: Typical Bypass Mode |
Holder: | Metal Bracket: Full Height/Low profile Height |
Operating Humidity: | 0%–90%, non-condensing |
Operating Temperature: | 0°C – 45°C (32°F - 113°F) |
Storage: | -40°C–65°C (-40°F–149°F) |
EMC Certifications: | FCC Part 15, Subpart B Class A Conducted Emissions Radiated Emissions CE EN 55022: 1998 Clas Amendments A1: 2000; A2: 2003 Conducted Emissions Radiated Emissions CE EN 55024: 1998 Amendments A1: 2000; A2: 2003 Immunity for ITE Amendment A1: 2001 CE EN 61000-3-2 2000, Class A Harmonic Current Emissions CE EN 61000 3-3 1995, Amendment A1: 2001 Voltage Fluctuations and Flicker CE IEC 6100-4-2: 1995 ESD Air Discharge 8kV. Contact Discharge 4kV. CE IEC 6100-4-3:1995 Radiated Immunity (80-1000Mhz), 3V/m 80% A.M. by 1kHz CE IEC 6100-4-4:1995 EFT/B: Immunity to electrical fast transients 1kV Power Leads, 0.5Kv Signals Leads CE IEC 6100-4-5:1995 Immunity to conductive surges COM Mode; 2kV, Dif. Mode 1kV CE IEC 6100-4-6:1996 Conducted immunity (0.15-80 MHz) 3VRMS 80% A.M. By 1kHz CE IEC 6100-4-11:1994 Voltage Dips and Short Interruptions V reduc >95%, 30% >95% Duration 0.5per, 25per, 250per |
MTBF: | 167 *According to Telcordia SR-332 Issue 2. Environmental condition – GB (Ground, Fixed, and Controlled). Ambient temperature 40°C. |
LEDs | |
LEDs: | (2) LEDs per port Link / Act Led: Turn on any Link speed , Blinks on Activity (green) Speed/Bypass/Disconnect (Bi-color) Led: 1000Mbit/s: Turns on Yellow 100Mbits/s: Turns on Green. 10Mbit/s: Turns off Disconnect: Blink Yellow Bypass: Blink Green |
LEDs location: | LEDs are integrated on RJ-45 connector |
Connectors: | (4) Shielded RJ-45 |
Part Code:
PE2G4BPi35LA