Silicom PE210G2BPi9 10G Bypass NIC Ethernet Intel

Condition: New

Silicom’s dual port fiber 10 Gigabit Ethernet Bypass server adapter is a PCI-Express X8 network interface card that contains two fiber (SR)10 Gigabit Ethernet ports on a PCI-E adapter. The Silicom’s dual port fiber (SR) 10 Gigabit Ethernet Bypass server adapter is targeted to inline network system that maintains network connectivity when system fails.

Silicom’s dual port fiber 10 Gigabit Ethernet Bypass server adapter supports Normal, Bypass and Disconnect modes. In Normal mode, the ports are independent interfaces. In Bypass mode, all packets received from one port are transmitted to the adjacent port. In Disconnect mode, the adapter simulates switch / rout cable disconnection. Silicom Bypass server adapters can Bypass or disconnect its Ethernet ports on a host system failure, power off, or upon software request.

In Bypass mode, the connections of the Ethernet ports are disconnected from the system and switched over to the other port to create a crossed connection loop-back between the Ethernet ports. Hence, in bypass mode all packets received from one port are transmitted to the adjacent port and vice versa. This feature enables to bypass a failed system and provides maximum up time for the network.

Silicom’s dual port fiber 10 Gigabit Ethernet Bypass server adapter includes an on board WDT (Watch Dog Timer) controller. The adapter’s software drivers or software application can write commands to the on board WDT controller. The adapter’s software drivers, WDT controller and the Bypass circuitry provide an interface that control and manage the mode of the adapter.

Silicom’s dual port fiber 10 Gigabit Ethernet Bypass server adapters are based on Intel 82599ES Ethernet controller

Bypass / Disconnect:

Bypass / Disconnect Ethernet ports on Power Fail, System Hangs or Software Application Hangs
Software programmable Bypass, Disconnect or Normal Mode
On Board Watch Dog Timer (WDT) Controller.
Software programmable time out interval.
Software Programmable WDT Enable / Disable counter.
Software programmable Bypass Capability Enable / Disable.
Software Programmable Disconnect Capability Enable / Disable.
Software Programmable mode (Bypass, Normal or Disconnect mode) at Power up
Software Programmable mode (Bypass, Normal mode) at Power off
Independent Bypass operation in every two ports.
Emulates standard NIC

Fiber 10 Gigabit Ethernet 10GBASE-SR:

10 Gigabit Fiber Ethernet port supports 10GBASE-SR (850nM LAN PHY)
10 Gigabit 850nM Small form Factor Pluggable (SFP+)

Fiber 10 Gigabit Ethernet 10GBASE-LR:

10 Gigabit Fiber Ethernet port supports 10GBASE-LR (1310nM LAN PHY)
10 Gigabit 1310nM Small form Factor Pluggable (SFP+)

Fiber 10 Gigabit Ethernet 10GBASE-SR5 (SR 50uM):

10 Gigabit Fiber Ethernet port supports 10GBASE-SR (850nM LAN PHY)
10 Gigabit 850nM Small form Factor Pluggable (SFP+)

-SRD: Fiber 1/10 Gigabit Ethernet 1000Base-SX / 10GBASE-SR:

10 Gigabit Fiber Ethernet port supports 10GBASE-SR (850nM LAN PHY)
1Gigabit Fiber Ethernet port supports 1000BASE-SX (850nM LAN PHY)
1/10Gigabit 850nM Small form Factor Pluggable (SFP+)

-LRD: Fiber 1/10 Gigabit Ethernet 1000Base-LX / 10GBASE-LR:

10 Gigabit Fiber Ethernet port supports 10GBASE-LR (1310nM LAN PHY)
1Gigabit Fiber Ethernet port supports 1000BASE-LX (1310nM LAN PHY)
1/10Gigabit 1310nM Small form Factor Pluggable (SFP+)

Fiber 10 Gigabit Ethernet 10GBASE-SR5 (SR 50uM):

10 Gigabit Fiber Ethernet port supports 10GBASE-SR (850nM LAN PHY)
10Gigabit 850nM Small form Factor Pluggable (SFP+)

Performance Features:

IPV4 and IPV6 Supports for IP/ TCP and IP/UDP Receive Checksum offload
Fragmented UDP checksum offload for Packet Reassembly
CPU utilization- the 82599 supports reduction in CPU utilization, mainly by supporting Receive Side Coalescing (RSC)
Support for 16 virtual machine Device Queues ( VMDq) per port
Support Direct Cache Access ( DCA)
Advanced memory architecture reduces latency by preceding TSO packets. A TSO packet may be interleaved with other packets going to the wire
Minimized device I/O interrupts using MSI and MSI-X
Offload of TCP / IP / UDP checksum calculation and TCP segmentation
Large on chip receive packet buffer (512 KB)
Large on chip transmit packet buffer ( 160 KB)
Supports the VPD (Vital Product Data) capability defined in the PCI specification ver. 3.0.
Time sync- IEEE1588- Precision Time Protocol (PTP)
Supports the BCN (Backward Congestion Notification) protocol in addition to the EEDC functionality

Host Interface:

PCI Express X8 lanes
Support PCI Express Base Specification 2.0 (5GT/s)

Common Key Features:

IEEE 802.x flow control support
IEEE 802.q VLAN tagging support
Supports a mode where all received and sent packets have at least one VLAN tag in addition to the regular tagging
IEEE 802.1p layer 2 priority encoding
Jumbo Frame (up to 16KB)
Link Aggregation and Load Balancing
RFC2819 RMON MIB statistics
TCP Segmentation Offload Up to 256KB
Ipv6 Support for IP/TCP Receive Checksum Offload
DDP Offload
LEDs indicators for link/Activity/Bypass/ Disconnect Mode status
Hot Plug not supported. Can be supported by assembly change
Low power
LC connector

Bypass Specifications:
WDT Interval (Software Programmable):	3,276,800 mSec (3,276.8 Sec): Maximum 100 mSec ( 0.1 Sec) : Minimum WDT Interval = (2^wdt_interval_parameter)*(0.1) sec. wdt_interval_parameter: { Valid Range: 0-15}
Fiber 10 Gigabit Ethernet Technical Specifications - (10Base-SR) Adapters:
IEEE Standard / Network topology:	Fiber 10 Gigabit Ethernet, 10G BASE-SR (850nM)
Data Transfer Rate:	10.3125GBd
Cables and Operating distance: Up to:	Multimode fiber: 62.5um, 160MHz/Km 13m 62.5um, (OM1)200MHz/Km 16m *Theoretical Distance – Defined as half a distance as stated by the IEEE 802.3-2005 standard
Optical Output Power:	Normal Mode (Bypass Off): Typical: -3.1dBm (TX –Switch Normal – Fiber – LC/LC) Minimum: -7.3 dBm
Optical Receive Sensitivity:	Normal Mode (Bypass Off) Typical: -15.37 dBm Maximum: -11 dBm
Insertion Loss:	Bypass Mode: Insertion loss (Optical Power attenuation between TX to RX) (LC- fiber- switch- LC) Typical: 0.39 dB (From RX to TX) Maximum 1.6 dB
Fiber 10 Gigabit Ethernet Technical Specifications - (10Base-LR) Adapters:
IEEE Standard / Network topology:	Fiber 10 Gigabit Ethernet, 10G BASE-LR (1310nM LAN PHY)
Data Transfer Rate:	10.3125GBd
Cables and Operating distance: Up to:	Single-Mode: 5000m at 9um* Defined as half a distance as stated by the IEEE 802.3 standard
Optical Output Power:	Normal Mode (Bypass Off): Minimum: -5.2 dBm
Optical Receive Sensitivity:	Normal Mode (Bypass Off) Maximum: -12.6 dBm
Insertion Loss:	Bypass Mode: Insertion loss (Optical Power attenuation between TX to RX) (LC- fiber- switch- LC) Maximum 0.5 dB
-SRD: Fiber 1000BASE-SX / 10GBASE-SR Technical Specifications:
Optical Output Power (1G):	Minimum: -10.9 dBm
Optical Receive Sensitivity (1G):	Maximum: -15.6 dBm
Insertion Loss (1G)	Maximum: +1.9 dBm
Output Transmit Power (10G):	Minimum: -7.3 dBm
Optical Receive Sensitivity (10G):	Maximum: -11 dBm
Insertion Loss (10G):	Maximum: 1.6 dBm
-LRD: Fiber 1000BASE-LX / 10GBASE-LR Technical Specifications:
Optical Output Power (1G):	Minimum: -10.8 dBm m
Optical Receive Sensitivity (1G):	Maximum: -19 dBm
Insertion Loss (1G):	Maximum: +0.5dBm
Output Transmit Power (10G):	Minimum: -5.2dBm
Optical Receive Sensitivity (10G):	Maximum: --12.6 dBm
Insertion Loss (10G):	Maximum: +0.5 dBm
Fiber Gigabit Ethernet Technical Specification - (10G Base-SR5 50uM) Adapters:
IEEE Standard / Network topology:	Fiber Gigabit Ethernet, 1000Base-SR (850nM)
Data Transfer Rate:	10.3125GBd
Cables and Operating distance:	Multimode fiber: 62.5um, 160MHz/Km 26m 62.5um, (OM1)200MHz/Km 33m 50um, 400MHz/Km 66m 50um, (OM2)500 MHz/Km 82m 50um, (OM3)2000MHz/Km 300m
Optical Output Power:	Normal Mode (Bypass Off): Typical: -3.27 dBm (TX Switch Normal – Fiber – LC/LC) Minimum: -6.3 dBm
Optical Receive Sensitivity:	Normal Mode (Bypass Off) Typical: -15.37 dBm Maximum: -7.5 dBm
Insertion Loss:	Bypass Mode: Insertion loss (Optical Power attenuation between TX to RX) (LC- fiber- switch- LC) Maximum 1.8 dB Typical: 0.78 dB (From RX to TX)
Operating Systems Support:
Operating system support:	Linux FreeBSD Vmaware
General Technical Specifications
Interface Standard:	PCI-Express Base Specification Revision 2.0 (5GT/s)
Board Size:	Low profile add-in card: 167.65mm X 68.91mm (6.60”X 2.713”)
PCI Express Card Type:	X8 Lane
PCI Express Voltage:	+12V ± 15%
PCI Connector:	Gold Finger: X8 Lane
Controller: :	Intel 82599ES
Holder:	Metal Bracket
I/O:	LC located on internal bracket
Weight:	200g (7.055Oz)
Power Consumption:	PE210G2BPI9-SR 6.6 W, 0.55 A at 12V: Typical all ports operate at 10Gb/s, (Normal Mode). 6.12 W, 0.51 A at 12V: Typical Bypass Mode. 6.36 W, 0.53 A at 12V: Typical No link at all ports
Operating Humidity:	0%–90%, non-condensing
Operating Temperature:	0°C – 50°C (32°F – 122°F)
Storage:	-20°C–65°C (-4°F–149°F)
EMC Certifications:	FCC Part 15, Subpart B Class B Conducted Emissions Radiated Emissions CE EN 55022: 1998 Class B Amendments A1: 2000; A2: 2003 Conducted Emissions Radiated Emissions CE EN 55024: 1998 Amendments A1: 2000; A2: 2003 Immunity for ITE Amendment A1: 2001 CE EN 61000-3-2 2000, Class A Harmonic Current Emissions CE EN 61000 3-3 1995, Amendment A1: 2001 Voltage Fluctuations and Flicker CE IEC 6100-4-2: 1995 ESD Air Discharge 8kV. Contact Discharge 4kV. CE IEC 6100-4-3:1995 Radiated Immunity (80-1000Mhz), 3V/m 80% A.M. by 1kHz CE IEC 6100-4-4:1995 EFT/B: Immunity to electrical fast transients 1kV Power Leads, 0.5Kv Signals Leads CE IEC 6100-4-5:1995 Immunity to conductive surges COM Mode; 2kV, Dif. Mode 1kV CE IEC 6100-4-6:1996 Conducted immunity (0.15-80 MHz) 3VRMS 80% A.M. By 1kHz CE IEC 6100-4-11:1994 Voltage Dips and Short Interruptions V reduc >95%, 30% >95% Duration 0.5per, 25per, 250per
*MTBF:**	71 (Years) * According to Telcordia SR-332 Issue 2 Environmental condition – GB (Ground, Fixed, Controlled). Ambient temperature 40°C
LEDs
LEDs:	(2) LED per port Link: Turns on Blue on 10G link. Turns on Green on 1G link ACT: Blinks on activity (green). Bi-color LED per Bypass pair: BYPASS: Turns on Green on Bypass Disconnect : Turns on Yellow on Disconnect Normal: Off
LEDs location:	LEDs are located on the PCB, visible via holes in the metal bracket holder
Connectors:	(2) LC